Ricoh AP505 Instructions d'exploitation

RICOH COLOR LASERPRINTER AP505OPERATING INSTRUCTIONSRead this manual carefully before you use this product and keep it handy for future reference. For

6 Operating InstructionsThis component Does this(1) Toner cartridge Houses the toner for the printer.(2) Fuser oil bottle Holds oil for fusing the to

7 Reviewing the Operation PanelReviewing the Operation PanelThis section describes the operation panel keys and their function. The following diagram

8 Operating Instructions(3) keyPress this key to switch the printer between on-line and off-line conditions.(4) keysUse these keys to select values

9 Turning Your Printer OnTurning the Printer On and OffThis following sections describe how to turn your printer on and off.Turning Your Printer OnFol

10 Operating InstructionsTurning Your Printer OffFollow the instructions below to turn your printer off:1 Confirm that the Data In and Error indicato

11Installing Options2Reviewing the Available OptionsThe diagram below illustrates the three options that are available for this printer.The following

12 Operating InstructionsInstalling the Memory Unit Type 505 (DIMM)Follow the instructions below to install the memory unit:Warning: Make sure to tur

13 Installing the Memory Unit Type 505 (DIMM)5 Push it in and close the white tabs (3). The diagram below illustrates the order in which you install t

14 Operating Instructions7 Plug the printer’s power cord back into the printer and the wall socket. Turn on the printer’s power switch.8 Print a conf

15 Installing the Printer Hard Disk Type 5054 Make sure that the projection of the connector on the hard disk is on the top. Attach the connector to t

Ricoh Corporation© 1999 Ricoh Co., Ltd.This equipment has been tested and found to comply with the limits from a Class B digital device, pursuant to P

16 Operating InstructionsThe printer starts initializing the hard disk. A message appears on the panel display, INITIALIZING.10 When initialization i

17 Installing the Paper Feed Unit Type 3053 Move the printer to make an installation space.Caution:Be careful when lifting the printer, as the right f

18 Operating Instructions5 Remove both pieces of adhesive tape.6 Pull out the paper tray and remove the padding.7 Remove the ring attached to the red

19 Installing the Paper Feed Unit Type 30510 Align the printer with the 4 upright pins on the paper feed unit and then lower it gently.11 Connect all

20 Operating Instructions

21Loading Paper3Reviewing the Paper Loading OptionsThe following procedure explains how to load paper in the trays. It also explains how to specify th

22 Reviewing the Paper Loading Options3 Load paper into the tray with the print side up.Caution:Make sure that the paper fits under the back paper gu

23 Specifying Paper Size Using the Operation Panel5 Slide the paper tray completely into the printer.Caution:Be sure to insert the paper tray complete

24 Reviewing the Paper Loading OptionsLoading Paper in the Bypass TrayFollow the instructions below to load paper in the bypass tray:Note: Do not ope

25 Loading Paper in the Bypass Tray3 Slide out the bypass tray extender.4 Load paper until it stops with the print side down.Caution:Make sure the pap

CONTENTSiiiChapter 1 Getting StartedGuide to the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Reviewing Exterior-Front View Co

26 Reviewing the Paper Loading OptionsSpecifying Paper Size Using the Operation PanelUse the following procedure to specify the paper size from the p

27Troubleshooting4Troubleshooting and Maintaining the PrinterThis section describes the procedures necessary for troubleshooting and maintaining your

28 Operating InstructionsIs the Data In indicator blinking after starting the print job?If not, the data is not being sent to the printer. The printe

29 Removing Misfed Paper from the Input TrayRemoving Misfed Paper from the Input TrayWhen a paper misfeed occurs, and error message appears on the pan

30 Operating InstructionsRemoving Misfed Paper from the Bypass TrayFollow the instructions below to remove the misfed paper from the bypass tray.To r

31 Removing Misfed Paper from the Front Cover2 If the paper is in the front side of the photoconductor unit, carefully pull it out.3 When the misfed p

32 Operating InstructionsRemoving Misfed Paper from the Output TrayFollow the instructions below to remove any misfed paper from the output tray:To r

33 Removing Misfed Paper from the Output Tray5 When you cannot see the misfed paper inside the printer, remove the misfed paper from the output tray w

34 Operating InstructionsReplacing the Toner CartridgeYou should replace the toner cartridge whenever the TONER LOW XXX message appears on the panel

35 Replacing the Toner Cartridge3 Carefully pull out the toner cartridge.4 Hold the grip of the toner cartridge and slide it out until you can see the

iv

36 Operating Instructions7 Hold the new toner cartridge and shake it with a horizontal motion, about 10 times, as shown in the diagram below.Caution:

37 Replacing a Specific Toner Cartridge10 Pull the tape out as shown in the diagram below.Caution:Be sure to pull the tape horizontally. Pulling it up

38 Operating InstructionsThe following message appears on the panel display SELECT TONER NO.3 Use the  and  arrow keys to select YES, and then pres

IndexIndex-1AAdjustpaper size dial 22Arrow keys 8BBack plate 4Bottletoner waste 6Bypass tray 24, 30CCancel key 8Charger 6Connectornetwork interface 10

Operating InstructionsIndex-2MMemory unit type 505 (DIMM) 12Menu key 8Misfed paperremoving from bypass tray 30removing from input tray 29removing fr

1Getting Started1Guide to the PrinterThis manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versa

2 Operating Instructions(3) Output tray Used to stack printed pages.(4) Output tray extender Used for printing on long paper.(5) Operation panel Show

3 Reviewing the Exterior-Rear View ComponentsReviewing the Exterior-Rear View ComponentsThis section describes the components of the exterior-rear vie

4 Operating Instructions(3) Ventilator This hole allows the air to circulate, preventing components inside the printer from overheating.Caution:Do no

5 Reviewing the Interior ComponentsReviewing the Interior ComponentsThis section describes the interior components of the laser printer. The following