Ricoh SP 213w Guide de l'utilisateur

1Model No.SP 212/SP 213 SeriesWi-Fi Settings GuideIntroduction ◆There are two wireless LAN modes: infrastructure mode for connection through an access

10 Press the [Stop/Start] key in the three-second period during which the three indica-tors sequentially flash.The PIN code will be printed.•The [Wi-

11Connection has failed: ◆The alert indicators start flashing, then, after 30 seconds, the alert indicator goes out and the power indicator lights con

12 Click the [Wireless] tab.Configure settings as follows:DCT86441321. Select [Setup with WPS].2. Select [Wi-Fi Protected Setup with PIN Code].3. Y

13 Check the result.Connection has succeeded: ◆When "Connected to the access point." is displayed, the connection has been estab-lished.Co

14 Click the [Wireless] tab.Configure settings as follows:DCT86612 1. Select [Manual Setup].2. Select [Infrastructure]. Configure the SSID and encry

15A. Connecting to devices using the WPA2-PSK or Mix Mode WPA2/WPA au-thenticationFor details about checking the SSID and encryption key, see page 2

16B. Connecting to the devices using the Open System or Shared Key authen-ticationFor details about checking the SSID and encryption key, see page 2

17 Check the result.Connection has succeeded: ◆The [Wi-Fi] key changes from flashing to continuous lighting.Connection has failed: ◆The alert indicato

18Using the Web Image MonitorWeb Image Monitor is a device-monitoring tool which allows you to configure the machine set-tings using the Web browser o

19If the encryption method is set to [CCMP (AES)] or [TKIP/AES] ◆1DCT8841. Enter the encryption key for the access point (router).If the encryption m

21. Before Configuring Wireless LAN SettingsChecking the Wireless LAN Access Point (Router)This information is required when you configure wir

20 Check the result.Connection has succeeded: ◆The [Wi-Fi] key changes from flashing to continuous lighting.Connection has failed: ◆The alert indicato

214. Configure the Wireless LAN (SP 212SNw/SP 212SUw/SP 212SFw/SP 212SFNw/ SP 213SNw/SP 213SUw/SP 213SFw/SP 213SFNw)Enabling Wireless LAN Press

22 Press the [User Tools] key to return to the Initial screen.A password for accessing the [Admin. Tools] menu can be specified in [Admin. Tools Lock]

23 Press the WPS button on the access point (router) within two minutes.WPSCHV607If the connection is successful, "Connection to AP has Succeeded

24 Hold down [Wi-Fi] key.DCT853If [Wi-Fi Enable] is set to [Disable], you cannot use the [Wi-Fi] key. Press [PIN]. Check the PIN code.PINPIN Code:XXXX

25Manual SetupIf you cannot check the settings of the access point (router) being used or the access point (router) does not support W

26 Search the SSID to display the list, select the destination SSID, and then press [Next].If you cannot find the destination SSID, configure the SSID

27Connecting to devices using the WPA2-PSK or Mix Mode WPA2/WPA au-thentication Enter the encryption key using the number keys, and then pre

28 Press [Yes]. Check the connection using [Wi-Fi Status].[User Tools] key [Network Settings] [Wi-Fi] [Wi-Fi Status]When "Connected" i

295. TroubleshootingConnection ProblemsIf problems occur even after you configure the connection settings again, check the following:Are the settings

3Number of characters used for the encryption keyThe number of characters used for the encryption key varies.Authentication EncryptionWEP Key LengthWE

30Connection was Successful but Wireless LAN Cannot be UsedIf a connection has been established but the wireless LAN cannot be used, check the followi

31Glossary of Wireless LAN TermsWireless LAN Access Point (Router)•This device routes data between wireless LAN-capable devices and the Internet.Infr

© 2014EN GB EN US EN AU M213-862632

4SP 212SNw/SP 212SUw/SP 212SFw/SP 212SFNw/SP 213SNw/SP 213SUw/ SP 213SFw/SP 213SFNw Press the [User Tools] key.DCT845 Press the [ ] or [ ] key to se

52. Checking Your Wireless Network EnvironmentCheck which wireless LAN settings you need to configure using the following chart:The connection method

63. Configure the Wireless LAN (SP 212w/SP 212Nw/SP 213w/SP 213Nw)Easy Setup Using the WPS ButtonIf the access point (router) cannot be detected

7 Press the WPS button on the access point (router) within two minutes.WPSCHV607 Check the result.Connection has succeeded: ◆The [Wi-Fi] key changes f

8 Click the [Wireless] tab.Configure settings as follows:DCT863123 1. Select [Setup with WPS].2. Select [Wi-Fi Protected Setup with Push Button].3.

9Easy Setup Using a PIN CodeIf the access point (router) cannot be detected within two minutes, the search session expires.•Device availabilityContro