Ricoh MP5125A Manuel d'utilisateur

NOTICEThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of theFCC Rules. These limit

Explains the system environment required for using the drive as a CD-R/CD-RW drive.PC IBM PC/AT compatibleOperating System Windows Me/98/95(ORS2 or la

Front Panel Rear panelFront PanelDisc trayThis is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push

Emergency eject holeThis drive has a function that allows the disc to be ejected manually for an emergency case such asfailure of the drive or a power

Emergency EjectThis drive has a function that allows the CD to be ejected manually, if this becomes necessary in anemergency such as failure of the dr

Disc ejectionPress the eject button1. Slowly take the disc out of the disc tray2. Press the eject button or push the disc tray and the tray will be

CautionAfter ejecting the disc, return the disc tray inside the unit quickly. When the disc tray is inthe ejected position, dust and other debris will

Load the mediaPress the eject button.1. Place the media on the disc tray.Be careful not to touch the recording surface of the media.CautionsDVD-R/RW

Load the disc by pressing the eject button or by lightly pushing in the disc tray.3. Next

Load the mediaDisc ejectionEmergency Eject Using the Drive in a Vertical Position

Using the Drive in a Vertical PositionThe drive can be installed in a vertical position.Locate the four tabs on the disc tray.Turn each of them inward

CAUTIONRating voltage for peripherals.1. Headphone Jack Rating Voltage output Audio Signal Max. 2V FCC WARNINGChanges or modification not expres

Specific knowledge of hardware and software is necessary to install the drive. We cannotguarantee against direct or indirect damage resulting from imp

1. Jumper Set UpBefore installation, set the jumper on the jumper connector on the rear panel.Master (MA)Drive set as Master (factory default)1. Slav

Only one jumper should be installed on the jumper connector. If more than onejumper is installed, the drive may malfunction or be damaged.● Next1. J

2. Removing the Computer CoverMake sure all peripheral devices of the computer and the computer itself are turned off, and thenremove the cover.Refer

3. Mounting the DriveRemove the 5 inch drive bay panel from the computer.Refer to the manual for the computer for details.1. Insert the drive unit in

Back Next1. Jumper Set Up 2. Removing the Computer Cover3. Mounting the Drive4. Connecting the Power Connector5. PC Connections 6. Sound Card Connecti

4. Connecting the Power ConnectorConnect the power cable from the computer's power supply to the socket on the drive unit,fitting the connector p

5. PC ConnectionsThe drive connects to the motherboard of the host computer using an IDE interface cable.Both Primary and Secondary connectors are usu

To Install as a Slave DriveWhen connecting the drive as a slave drive, change the position of the slave setting jumperpin on the rear of the system un

The company names and product names written in this manual are trademarks or registeredtrademarks.● *1 For information on Windows® XP supports, visi

Back Next1. Jumper Set Up 2. Removing the Computer Cover3. Mounting the Drive 4. Connecting the Power Connector5. PC Connections6. Sound Card Connecti

6. Sound Card ConnectionIf the computer has a sound card, the drive can be connected to the sound card with an audio cable.Make sure the connections a

1. Jumper Set Up 2. Removing the Computer Cover3. Mounting the Drive 4. Connecting the Power Connector5. PC Connections6. Sound Card Connection7. Repl

7. Replacing the Computer CoverWhen the installation of the drive unit is complete, replace the computer cover.Back Next1. Jumper Set Up 2. Removing t

8. Device DriversWhen using Windows 98/95, Window NT Workstation Ver. 4.0, Windows 2000 (Professional)Windows XP the installation of any special devic

After checking the above-mentioned points, contact the manufacturer of your PC or PCmother-board, if applicable, to obtain an appropriate IDE controll

CautionWhen using CD-ROM/DVD-ROM/CD-R/CD-RW/DVD+RW/DVD+R media, do not attachany stickers or labels to the media. Using discs with labels attached not

Drive : MP5125ATypeInternal typeInterfaceEnhanced-IDE (ATAPI)Data buffer memory2MBData transfer speed33.3MB/sec. (Max.) (Ultra DMA mode2)CD-RW/High Sp

Video-CD* * CD-Text* * DVD+R* * DVD+RW* * DVD-ROM * Loading systemTray type (automatic loading/eject)Power DC5V, DC12VPower consumption16wWeightLess t

* All references to the product in this document are to specifications in effect when the product was released. Copyrig

This manual uses the following symbols to indicate important information relating to the drive.Failing to comply with the information in this manual a

This user's manual (hereafter referred to as "the manual") contains important notes andproduct handling information. Be sure to read th

Obey the following cautions when handling the drive or discs. Cautions During InstallationInstall the drive in accordance with the specifications. Be

In wintertime, don't use a disc soon after bringing in from outdoors. Use it only after ithas reached room temperature.● Cautions Concerning D

fig1Check1. Recording surface2. fig250 to 100mm1. Back

The drive is a super-combination drive that integrates DVD+RW/+R and CD-RWcapabilities. Capitalizing on Ricoh's expertise accumulated with existi